Leading 10 typical forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the workers used their body weight as the counterweight, which almost caused casualties.
Instance 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and fell from the automobile when it rolled over and was squashed.
Forklift procedure should take notice of these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe prior to starting.
3. When the forklift begins with a load, the motorist ought to initially confirm that the tons is stable and trusted.
4. The start has to be slow and constant.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be increased expensive, which will affect the security of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or cars nearby, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to shed side security and topple. .
5. When the forklift is downhill, it is strictly forbidden to shut off the flame and slide, and it is prohibited to brake instantly while driving with loads unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must maintain a particular security range from the vehicle in front. .
7. When the forklift is running, the lots has to be in the lowest placement that does not impede the driving, and the gantry must be effectively tilted back. The tons will not be elevated other than when piling or filling. .
8. The elevation of the tons should not block the chauffeur's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it has to drive securely at a low speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is forbidden for personnel to depend on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will be fixed and reported in a prompt manner, and they will certainly never ever operate with illnesses or hide them.

packing and unloading.
1. When fork-loading things, the distance in between both forks ought to be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with Stand-on Electric Pallet Stacker a single fork or make use of a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and dumping items, the forklift has to be braked with the brake. .
4. The rate of the vehicle need to be slow and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm people. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the load, and it needs to be kept in mind that the fork suggestion need to not touch other products or things. The tons must be supported with marginal back tilt of the gantry so that the tons does not Electric Forklift Truck for Warehouse glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork products at broadband and collide with hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water must be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you run into a person in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Running up and down the slope must be slow and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle should be driven backwards when worsening;.
8. When the forklift employees bring the goods and progress, if they encounter big or hefty products and most likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Solitary fork procedure is not enabled.
2. It is not permitted to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring people to deal with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Contours, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844